购得一款os1.3.几的nspire clickpad，想更新的时候卡在这里再不动，请问有何解决办?
如图。到这里后再不动了计算器上什么反应都没有‘ Check and report the current version of the calculator, please :) critor 发表于 2013-11-5 08:16 static/image/common/back.gif
Check and report the current version of the calculator, please :)
很糟糕的是我用格式化的那个菜单把系统清除了，现在只有boot1 1.1.8916
以及boot2 1.1.8981 critor 发表于 2013-11-5 08:16 static/image/common/back.gif
Check and report the current version of the calculator, please :)
os0.0.0 549597890 发表于 2013-11-5 09:39 static/image/common/back.gif
很糟糕的是我用格式化的那个菜单把系统清除了，现在只有boot1 1.1.8916
以及boot2 1.1.8981
Backup before any further operation.
折腾前先备份。 No {:tongue:}
OS 0.0.0 just means the OS has been removed.
549597890, is there any strange sign in the top left-hand corner of the screen when you turn on the calculator?
Anything like this?
http://www.cncalc.org/data/attachment/forum/201311/02/122331o0erqb7wgippzqpr.jpg critor 发表于 2013-11-5 21:27 static/image/common/back.gif
No
OS 0.0.0 just means the OS has been removed.
As same as you pic 549597890 发表于 2013-11-6 00:01 static/image/common/back.gif
As same as you pic
yes, i removed its os
by esc+home+P+on2-1 549597890 发表于 2013-11-6 00:02 static/image/common/back.gif
yes, i removed its os
by esc+home+P+on2-1
如果您懂汉语的话。就是我在有系统的时候就更新不了任何系统。格机后还是照旧，于是彻底瞎了
Ok, then you have a prototype and it's going to reject all production OSes available on education.ti.com.
You first have to mod it into a production model, and then you'll be able to upgrade it up to the 3.2 version.
A tutorial is available there:
http://www.cncalc.org/forum.php? ... 22&page=1#pid128123 critor 发表于 2013-11-6 01:22 static/image/common/back.gif
Ok, then you have a prototype and it's going to reject all production OSes available on education.ti ...
很抱歉昨晚说错了一件事实：我的屏幕左上没有水瓜设备那种标志。不过我在刷1.1系统的时候遇到跟他一样的问题，刷1。3或者更高时候会遇到如下图所示 critor 发表于 2013-11-6 01:22 static/image/common/back.gif
Ok, then you have a prototype and it's going to reject all production OSes available on education.ti ...
如图
This is a generic error message.
So nothing really wrong for now: just reboot the calculator and try again until it works or you get a specific error message. 本帖最后由 549597890 于 2013-11-7 16:23 编辑
critor 发表于 2013-11-7 01:50 http://www.cncalc.org/static/image/common/back.gif
This is a generic error message.
So nothing really wrong for now: just reboot the calculator and...
目前的情况：安装清除boot2的1.7能装上；安装有boot2的1.7 装上以后开机进度条走满以后死机，拔键盘也不会关闭
清除boot2的3.1系统invalid 没清除boot2系统invalid
正在尝试2.1....... 549597890 发表于 2013-11-7 16:22 static/image/common/back.gif
目前的情况：安装清除boot2的1.7能装上；安装有boot2的1.7 装上以后开机进度条走满以后死机，拔键盘 ...
断电后, 开机启动界面的左上角是否有个带点的方块?
是的话, 就是工程机, 请参照我写的教程刷机变成量产型, 否则 只能用工程机的boot2和OS,
与商业 版不通用...刷成商业版后才能升级到2.x, 3.x
http://www.cncalc.org/thread-9527-1-1.html 诗诺比 发表于 2013-11-7 16:37 static/image/common/back.gif
断电后, 开机启动界面的左上角是否有个带点的方块?
是的话, 就是工程机, 请参照我写的教程刷机变成量产型 ...
没有那个标志。
但是boot2确实太低了点。另外这是目前唯一能刷进去启动的系统。按照1.7上的ndless2教程装总会雪花屏幕，然后重启，安装失败。 549597890 发表于 2013-11-7 16:42 static/image/common/back.gif
没有那个标志。
但是boot2确实太低了点。另外这是目前唯一能刷进去启动的系统。按照1.7上的ndless2教程装 ...
不是工程机的话就好办了
先刷2.1的OS, 再刷3.X OS
注意 CAS和非CAS的OS是不同的 OS TI-Nspire™ (v 2.1.0)
http://tiplanet.org/forum/archives_voir.php?id=1898
OS TI-Nspire™ (v 3.1)
http://tiplanet.org/forum/archives_voir.php?id=3719
OS TI-Nspire™ (v 3.2.3)
http://tiplanet.org/forum/archives_voir.php?id=9678
诗诺比 发表于 2013-11-7 16:52 static/image/common/back.gif
OS TI-Nspire™ (v 2.1.0)
http://tiplanet.org/forum/archives_voir.php?id=1898
耍过咱们论坛的2.1不论有关/删不删boot2都不好用。我试试这个。跟boot2有关？跟ti link有关？
页:
[1]
2