Nspire Color EVT到手
一个月前在X宝买的原型机。
3.0.0.1503系统。
Boot1:3.0.0
Boot2:3.0.0
没有开发机标识。
型号显示为TI-Nspire TM CX
不过，开机画面还是绿色进度条。
只能在插USB的情况下开机，我推测电池损坏。
文件系统和OS都已经导出，请看附件。
前排 On the back of this calculator the series number is :
NSC EVT1N8 NOT FOR SALE 023
May I try to install a CX OS to this EVT?
我最清楚的成像设备就是这个扫描仪了。
ASIC：ET-NS2010A-0 T6UJ1XBG-0001
Memory:OHA98JW378 感谢去年朔雪的帖子，我没把主板连接口拆坏。
初步断定这台原型机就是去年出现过的型号，甚至更早一些。 Can not install any OS apart from which dumped from itself. {:021:}想当个买菜计算器用，还得插着充电宝。
Can be used as a primary calculator, with external battery plug in. 六合江山QQ 发表于 2013-10-9 20:46 static/image/common/back.gif
ASIC：ET-NS2010A-0 T6UJ1XBG-0001
Memory:OHA98JW378
内存是micron的128MB SLC+32MB LPSDR MCP，和CM上的相同，也与之前的color原型机相同。
如果没有问题，这台机子没法安装别的系统。
不过critor有提到，他的color原型机上有一个tsop封装的nor flash，厂商是MXIC，不知道你这个有没有。 六合江山QQ 发表于 2013-10-9 20:31 static/image/common/back.gif
我最清楚的成像设备就是这个扫描仪了。
扫描仪的图太小了，完全看不清…… nbzwt 发表于 2013-10-10 08:38 static/image/common/back.gif
内存是micron的128MB SLC+32MB LPSDR MCP，和CM上的相同，也与之前的color原型机相同。
如果没有问题，这 ...
有，在主板屏幕一面。
机身也是光滑的。
完全是去年出现过的那台一样型号。 nbzwt 发表于 2013-10-10 08:43 static/image/common/back.gif
扫描仪的图太小了，完全看不清……
应该是上传时压缩了。 充了一晚上电，终于能不插USB开机了。 {:019:}几分钟电量掉到75% 本帖最后由 critor 于 2013-10-10 22:20 编辑
Hi!
Nice find - thank you for the pictures and the dump.
Your 3.0.0.1503 is a development OS which was built on 8th February 2011.
The 3.0.0 Boot1 and Boot2 flashed in your TI-Nspire Color are development images: they'll only accept to run development OSes and not production OSes released on TI website.
For now, we've only dumped two other TI-Nspire CX development OSes and they are quite similar:
- 3.0.0.1045 built on 6th december 2010
- 3.0.0.DEVBUILD built on 14th february 2011
Note that the oldest one, 3.0.0.1045 is interesting as it includes an official builtin theme editor which was removed on later versions:
Source: http://tiplanet.org/forum/viewtopic.php?t=11089
Download: http://tiplanet.org/forum/archives_voir.php?id=10345
To install production OSes on your TI-Nspire Color, you'll either have to:
- Reflash the Boot1: this is possible as the Boot1 here is not in the proprietary ET-NS2010A-0 ASIC but on a publicly documented external Flash-NOR chip by MXIC you'll find on the other side of the board behind the J04 connector. We could achieve this on TI-Nspire ClickPad prototypes. You'll need to adapt our code for the different chip.
http://tiplanet.org/forum/gallery/image.php?album_id=143&image_id=1691
- Port Nlaunch CX for the 3.0.0 Boot2: You'll need to fix all syscall addresses, and other fixes are required to make Nlaunch CX run with only 32MB SDRAM instead of 64MB. critor 发表于 2013-10-10 22:12 static/image/common/back.gif
Hi!
Nice find - thank you for the pictures and the dump.
New prototype found on Taobao.
http://item.taobao.com/item.htm?spm=a230r.1.14.62.ByQ8Ke&id=18359078325
You may notice the wire attached to the top of this NS CX CAS.
Could you check your TI-Nspire Color Diagnostics version?
Diagnostics is started by holding the Esc+Menu+Minus keys while pressiong reset.
If it's version 3.00.102, you'll get a picture at the end of the "2. LCD" test, picture which has been removed on production diagnostics.
http://tiplanet.org/forum/gallery/image.php?mode=medium&album_id=13&image_id=1761 critor 发表于 2013-10-11 18:19 static/image/common/back.gif
Could you check your TI-Nspire Color Diagnostics version?
Diagnostics is started by holding the E ...
本帖最后由 critor 于 2013-10-11 19:21 编辑
Thanks. :)
Is it version 3.00.102 too? Version number can be found in "8. Information Screen".
页:
[1]
2